THE AVIATION SUPERSTORE FOR ALL YOUR AIRCRAFT & PILOT NEEDS | 877-795-2278

E3000 Ekostrip Gallon

$173.75/Each
Part# 09-03080
MFR Model# E3000-G

Overview

Stewart Systems EkoStrip is an environmentally safe paint stripper that can be sprayed, brushed or rolled on your painted surface. EkoStrip is not solvent borne and does not dry out and stop working overnight. In most cases the stripping action will take place in 2-4 hours. EkoStrip has no harsh odors, is not caustic and is biodegradable.

Reviews

I stripped two ruddervators and used about 3 quarts. I sprayed it on and them wrapped them in blach plastic sheeting in the late afternoon and by 9pm had very little action taking place. In the morning it progressed more, especially on some areas that had likely been repainted for repair at one time. Leaving it covered in the black plastic in the sun until 2pm made huge progress! Nearly the entire surface was wrinkled and could be removed without effort. There were still stubborn areas I had to keep reapplying, but this is the best stripper Ive used to date. It barely smells at all and even when I got it on my bare hands, didnt hurt, burn, or cause damage as long as I washed it off in a few minutes. A light pressure washing would have really sped up the process but I was overly cautious not to damage the parts. Other strippers were definitely not as environmentally friendly or safe for the applicator. The product went surprisingly further than I expected, even though I had to do several reapplications in stubborn areas.

Brian S Verified Purchase

E3000 Ekostrip Gallon

October 5, 2024

Other products I tried failed. It removed the paint after leaving overnight covered in plastic, then pressure washing in the morning. Sanding off primer required.

Kevin H Verified Purchase

E3000 Ekostrip Gallon

August 28, 2021

Worked very well at removing old paint off 1963 Cessna, the primer was a different story, nothing would take off the primer. I was very happy with this paint remover.

James B
April 6, 2018

Ive used many aircraft paint strippers and this is by far the best. For best results, Ive found that once applied, cover with plastic and leave it on overnight. It also doesnt eat through nitrile gloves like other strippers do. It has a mild almost pleasant smell to it. This stripper has cut the time it takes to strip parts at least in half for me.

Conrad L
August 23, 2017

Works good

Douglas E Verified Purchase

E3000 Ekostrip Gallon

June 7, 2022

I agree with James B on removing primer, I am stripping a 1960 172A. I tried covering with plastic and without with not much difference. I do see that if timed just right the primer is softer and can be scraped off but if left on past the point where paint bubbles it flashes and allows the primer to begin setting up. Overall good though. LWN

Lwn
September 27, 2018

Tried using it on some old paint (70s), barely softened it, hopefully itll work better on new paint, will advise.

Chandelle A Verified Purchase

E3000 Ekostrip Gallon

October 18, 2022

Unfortunately, even when used in a temperature controlled oven with the recommended procedures, EKOSTRIP had no effect on the lacquer used on brass musical instruments (trumpets, trombones, tubas)

Caswell M Verified Purchase

E3000 Ekostrip Gallon

October 19, 2021

Q&A

Please note, Aircraft Spruce Canada's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce Canada assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.

Q: Is this safe to use on plastic and fiberglass parts?

Per supplier: No, it is not recommended for use on either.

Q: Is this safe to use on plastic and fiberglass parts?

Per supplier: No, it is not recommended for use on either.

Q: Is this Ekostrip safe to remove Stewart Systems paint from fabric? (Ceconite)

Per Stewart Systems, paint remover is not recommended for any fabric covered parts.

Q: What temperature range will Stewart Systems Ekostrip work at?

The instructions say to use it between 80 & 100 degrees F. Best results at about 90 degrees F.

Q: What is the best method to deliver the stripper to the aircraft surface? Ideally Id like to spray on. Im considering using an airless paint sprayer (Graco X5). Is this recommended?

Yes, the instructions on the bottle indicate it can be sprayed on.

Q: What is the coverage per gallon of Ekostrip?

A gallon of P/N# 09-03080 will cover about 100 sq ft depending on how heavily it is applied.

Q: Can the Stewarrt Systems Ekostrip be used to strip lacquer based paints?

Per Vendor: As far as we are aware, P/N# E3000G (09-03080) should strip away any type of paint. If it needs, it can be reapplied or left on longer to remove the paint.

Q: I am re painting a beech skipper which has areas that are bonded with epoxy. Will this Stewart Systems Ekostrip stripper affect those joints?

Its best to keep this material away from any epoxy or composite material.

Q: Is this Stewart Systems Ekostrip flammable or combustible?

No, this is not flammable.

Q: Is Ekostrip safe to use on Cessna spring steel landing gear?

Yes. Ekostrip is safe for all metal. It is not safe for fiberglass or composite, and may harm some plastics.

View in Catalog

View Image View in Catalog