Money well spent
Owen O
Verified Purchase
Deluxe Model Brake Lining Tool
August 3, 2024
Works great
Marcus Z
Verified Purchase
Deluxe Model Brake Lining Tool
July 16, 2024
decent quality tool -- a suggestion though .maybe an instruction sheet or link to one online would be useful
Paul A
Verified Purchase
Deluxe Model Brake Lining Tool
June 7, 2024
Worked great. Had to grind a little off front to fit my brakes on a mooney.
Brian W
Verified Purchase
Deluxe Model Brake Lining Tool
March 12, 2024
Joseph W
Verified Purchase
Deluxe Model Brake Lining Tool
December 15, 2023
Worked very well both for removal and installation of rivets...dont over tighten rivet as that would lead to thread galling.
John G
Verified Purchase
Deluxe Model Brake Lining Tool
November 30, 2023
Fast shipping and good quality.
Roman S
Verified Purchase
Deluxe Model Brake Lining Tool
May 18, 2023
Works great.
Warren H
Verified Purchase
Deluxe Model Brake Lining Tool
June 28, 2022
Great easy tool!
Bob S
Verified Purchase
Deluxe Model Brake Lining Tool
March 17, 2022
You definitely want one of these tools to do the Cleveland brake systems. Takes a little feel to know how much to torque down the rivet so that you dont fracture the brake pad, although I did not have this problem. Great value for the price!
Neil G
Verified Purchase
Deluxe Model Brake Lining Tool
September 23, 2021
Needed a tool to last, looks like we got one for sure, Put some grease on the threads and
it did the job easily and looks like will be in the tool box for a long time.
Olathe S
August 18, 2020
Works as advertised.
David S
August 15, 2019
Great toll for the money
Frank S
February 4, 2019
The part that drives out the old rivet is weak. Otherwise, this is a good tool.
William E
Verified Purchase
Deluxe Model Brake Lining Tool
July 31, 2024
Looks like a great little tool, but unfortunately I had to return it, as it does not open far enough to put my brake shoes into it and use it.
Richard W
Verified Purchase
Deluxe Model Brake Lining Tool
March 26, 2024
Works well.
Bill J
October 5, 2018
Dont be cheep order the other one. This unit works but is cheep Chinese, not quite right low quality. Throat clearance isnt correct for Cleveland pad replacement. Needed a trip to the grinder.
Eric L
Verified Purchase
Deluxe Model Brake Lining Tool
May 24, 2022
It does work, but I would suggest getting the versio without the threads. One strike with a hammer would be easier than the torque needed to set the rivets with the threaded version. Also, removing the old rivets is made much easier by just drilling them with a bit smaller than the set side and punching them through with a nail set. Since adding the cost of the tool to a set of pads is still less than buying new backing plates you only have ot get one use out of it to make it economically a good decision. I mounded the tool in a vise and had little issue with it.
Dr. B
May 17, 2018
The tool works but it must be made of poor quality materials. I had to install 24 pins and by the 20th or so the threads on the screw were starting to gall. A little oil on the threads did not improve the action.
Eric L
April 20, 2017
Works well the first couple of times that you use it. After setting around 10-12 rivets, the threads starting galling and made the tool unusable. Poor quality.
Michael D
January 14, 2022
Borrowed this tool from our club, the rivet punch tip got bent after only a few rivets. What is this tool made of, aluminum? Poor quality, thats for sure.
Carlos
November 5, 2021
Very poor quality materials. I put a little center-point grease on the threads before I even started. After just two pads (6 rivets) the threads were starting to gall. By the time I finished a full set (12 rivets) I can barely turn it.
Imagine being able to strip a 8mm bolt with your hands and a 2 T-handle? Supplier is sending me a replacement, which I dont expect to be any better. ACS doesnt normally accept exchanges on tools. Get the Rapco tool instead.
Steve S
February 15, 2018
the rivet extractor pin broke after two rivet...
Benoit
August 20, 2017
Junk!
The punch tip bent after 4 rivets. The threads on the press collapsed and locked up after 8 rivets.
Jim D
November 25, 2018