The 2 in 1 hole punch is the easiest way you can make new instrument panel or add to current one. Punches through clean and precise, no sharp edges, and only takes a few seconds to do.

Sergey G Verified Purchase

ATS Instrument Hole Punch 2-1/4 & 3-1/8

Good material a d workmanship

Jorge L Verified Purchase

ATS Instrument Hole Punch 2-1/4 & 3-1/8

This Hole Punch works great, easily punches through tenth-inch aluminum for instrument panels. Makes nice, clean edge cuts.

Gailyn K Verified Purchase

ATS Instrument Hole Punch 2-1/4 & 3-1/8

High quality, works as described.

Steve W Verified Purchase

ATS Instrument Hole Punch 2-1/4 & 3-1/8

One of the best tools ever made regarding panel upgrades or new builds no matter what this is the way.

Airsports I Verified Purchase

ATS Instrument Hole Punch 2-1/4 & 3-1/8

Works great. Very clean holes, perfectly sized. Quality tool.

Patrick D Verified Purchase

ATS Instrument Hole Punch 2-1/4 & 3-1/8

Works well. What seems to work best is continue to tighten the nut until you hear two. I use it in combination with a hole jig.

Kenneth E Verified Purchase

ATS Instrument Hole Punch 2-1/4 & 3-1/8

Works good, lube threads and connect surface of nut before use

Eaa C Verified Purchase

ATS Instrument Hole Punch 2-1/4 & 3-1/8

Very nice tool and fits my needs

Oren R Verified Purchase

ATS Instrument Hole Punch 2-1/4 & 3-1/8

👏🚶👍👌

Douglas A Verified Purchase

ATS Instrument Hole Punch 2-1/4 & 3-1/8

Worked very well. Made short work of cutting instrument holes after lubing the threads. Just wait for the second click.

Life saver! Well more like time saver! Wow how quickly it was able to cut through .085 T3 aluminum, took some effort at the end with sheetmetal this thick, but it did it and it did not warp or bend as anticipated. Its worth the money....as I always say...time is money and what is your time worth?? Highly recommend! Great tool, high quality.

Great tool.. I was reluctant to purchase this tool based on the reviews. I went ahead and ordered it and it works great. Punched 8 holes in a 6061 T6 .90 dash panel the first day I had it and it was simple.

i am amazed how quickly it arrived. great tool used it to punch over 21 holes already works great a quality tool well made highly recommend both tool and your company. if i could give more stars i would this coming from a military aircraft structural mechanic first class ray reininger

Works great!

Good for popping quick holes. Will warp the metal depending on thickness. I bought this to make a panel overlay with some .032 aluminum and was left with some warping outside of the instrument hole. Cut a new hole for a G5 in my thinner primary panel and this was perfect for that job.

Nice product for making very clean instrument holes. Only made a few so far so I cant tell you if blades dull quickly after use or not. Only down side was no instructions for use, however you can play with it and figure it out quick enough. Basically sandwich the sheet metal between the cutting piece and hole and turn the nuts until it punches through.

Threads stripped on the third hole I punched. Using it on 1/8 inch aluminum for 2.25 holes. I have an $30 Amazon die for 2” holes that melts through the same material. For the money…shouldn’t have this problem.

I punched two 2 1/4 holes and two 3 1/8 holes in a 16 ga. (0.062) aluminum 6061 Instrument panel. The threads on the 5/8 thru shaft that is used to line up the punch and apply the necessary torque was not hardened and the threads stripped making the punch useless! I need a replacement 5/8 shaft to do use this punch again.

I understand that Spruce does not make this tool. It is an ATS product. My problem is that, after inspection of the tool itself, the 5/8 shaft of this toll is out of concentricity from the cutting diameter by almost 1/8. After insuring the my initial pilot hole was on center, the resultant instrument hole was 1/8 out! This is very poor quality. Maybe ATS keeps the good ones for sale on their own website and sends the others out for resale. Note that the package that ATS sells on their website includes a supposed template that supposed to align the final instrument hole. I dont know how this will help, however, when the tool itself is janky.

The claim that this tool is suitable for up to 0.125” aluminum is not correct. We u it on 0.086” aluminum and didn’t even get one hole made before the thread of the center bolt stripped. It required so much torque that it warped the material and there’s absolutely no way it would work with other instruments installed like suggested in the description as it requires a long handled socket on each side and a lot of muscle. Very disappointed and will be attempting to return.