FREE SHIPPING ON ORDERS OVER $699 (SOME EXCLUSIONS APPLY) | 877-795-2278

J-23502-1 Cessna Mount Kit

$1427.00/Each
Part# 07-19181
MFR Model# J-23502-1
DescriptionMount No.Part Number
Lord Elastomeric Engine Mount
see * for models
(includes: 2/J-9613-49 & 2/J-9613-72)
*J-23502-107-19181

Overview

Note: Please review application guide below to confirm correct part number for your aircraft.

Lord Engine Mount Application Guide (PDF)

These compression type couplings consist of bonded rubber joints pressed into the sockets of metal hubs. These dynafocal engine suspensions provide proper flexible support to isolate engine vibrations and reduce noise transmission to airframe structure in all aircraft applications. Careful design assures maximum strength to hold the engine under ultimate load and emergency conditions. Suspensions also distribute loads in most desirable patterns, control engine motions, accommodate thermal expansion and manufacturers’ tolerances.

*J-23502-1

SERIAL No.

MAKE and MODEL

172Q

Skyhawk S/N17275869 on

1 Lyc 0-360-AL/N

172Q

Cutlass S/N 17275869

1 Lyc 0-360-AL/N

172R,S

Skyhawk

1 Lyc 0-360-L2A

172RG

Cutlass

1 Lyc 0-360-AlF6

 

Warranty

  • All Parker Lord general aviation engine mounts come with a 5-year limited warranty, which is retroactive. Included in the prorated warranty are engine mounts for Cessna, Cirrus, Mooney, Piper and all other general aviation models serviced through official Parker Lord distributors. Experimental or acrobatic aircraft are not covered under this warranty. Normal wear and tear expected to occur with regular use and maintenance is also excluded. All warranty claims are pending evaluation by Parker Lord. Please contact customer service for assistance with any warranty claim.
  • Life of the Part since Purchased0-36 Months37-42 Months43-48 Months49 - 54 Months55 - 60 Months61 Month and more
    Amount Reimbursed100%50%40%25%10%0%
  • Frequently Purchased With
  • Customers Also Viewed

Reviews

As advertised and grateful you had this in stock. These look like great quality, too.

Aaron L Verified Purchase

J-23502-1 Cessna Mount Kit

September 10, 2024

Worked great...as advertised 👍

Hugh B
March 18, 2021

Over priced!!!!!

Thad L
February 1, 2021

Replaced same mounts that finally failed.

Comstock A
September 30, 2020

EGT/CHT is good quality and all of the parts needed were included in the basic system.

Lt
September 9, 2020

Petfect

Rick S
June 19, 2020

Very good mount

Joe
October 27, 2019

I replaced my 25 year old mounts on my 172 with these and the difference was amazing! On the first flight you could feel the difference with all vibration smoothed out. Great product!

Andrew R
September 28, 2017

I returned the items because they didnt fit my aircraft.

Jim B
December 17, 2020

They work fine, but the service life is rather short. I have to replace them every few years. At more than $ 20 per mount and 10 mounts in the cowling it is a considerable expense. I feel that there should be more durable materials available at the current level of technology.

Ivan B
October 28, 2019

Q&A

Please note, Aircraft Spruce Canada's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce Canada assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.

Q: Is the price for the Lord Elastomeric Engine Mounts for a set or for each one?

The are priced and sold individually. So if your aircraft requires Qty 4, then you will need to purchase Qty 4 of the correct part number.

Q: Do the Lord mounts listed here contain 2 half rubber parts + spacer?

Yes, Lord mount J-12390-1 for example, has 2 halfs and a spacer.