Aircraft Spruce Canada
Brantford, ON Canada
Corona, CA | Peachtree City, GA
Chicago, IL | Wasilla, AK
Aircraft Spruce Canada- Wishlists
- 1-877-795-2278
- Contact Us
Contact Us
Call Us
Sign In
Dynon Skyview SV-ADSB-472 ADS-B In Dual Channel Receiver
MFR Model# 102985-000
Overview
|
Note: for use with the Dynon Skyview system only. Dynon’s dual band ADS-B receiver receives weather & traffic on both 978 MHz and 1090 MHz frequencies. The dual band SV-ADSB-472 receives ADS-B traffic via 978 MHz (UAT) and 1090 MHz. In the US, it also receives free text and graphical weather from the FAA’s network of ADS-B ground stations. Unlike portable ADS-B receivers, you get FULL ADS-B and radar traffic when you pair this with our Mode-S transponder. The remote mounted receiver utilizes an externally mounted antenna for superior ADS-B reception. The ADS-B antenna must be installed at least two-feet from the transponder antenna. ADS-B Weather: Subscription-free weather displayed on SkyView, including NEXRAD radar, METARs and TAFS. Airport weather data can be displayed for nearest airports or for a specific airport identifier.
TFR Information: TFR NOTAMs are displayed graphically on the navigation map. Antenna Information: The SV-ADSB-472 requires its own antenna; it cannot share the transponder's antenna. A UAT-specific antenna or a transponder antenna may be used with the SV-ADSB-472. Please note any ADS-B unit will operate within the USA only when in clear line of sight of an ADS-B tower (flying at a higher altitudes may be required to gain proper signal). For more information please visit:FAA Link
|
Specifications
- Dimensions: The SV-ADSB-472 is approximately 2.79" x 4.10" x .97" in outside dimensions.
- Weight: 0.3 lb. (0.12 kg)
- Power: 0.05A @ 12V DC
Harness
- Part No. 11-11938 (DYNON SKYVIEW ADS-B WITH 4FT HARNESS): Comes with 4 ft leads for power, ground, and data lines.
- Part No. 11-11939 (DYNON SKYVIEW ADS-B WITH CUSTOM HARNESS): Required questions in the shopping cart regarding lengths of various connectors.
- Note: Antenna connector is female BNC Out. Need a male BNC to connect to.
Reviews
Light product, easy to install. There is a specific harness with supply+ground+RS232 , it is not connected thru skyview network
Verified Purchase
Dynon Skyview SV-ADSB-472 ADS-B In Dual Channel Receiver
Dynon dual channel adsb rcvr arrived quickly and was easy to install. Now seeing much more traffic compared to the old UAT only rcvr.
Verified Purchase
Dynon Skyview SV-ADSB-472 ADS-B In Dual Channel Receiver
Looks good
Verified Purchase
Dynon Skyview SV-ADSB-472 ADS-B In Dual Channel Receiver
Functioned well.
A neat setup to make you ADSB work on your Dynon
I have not installed it yet but I have bought Dynon b3fore and have been pleased.
These are made (I guess) by Dynon. I wish the wires ends were marked as to where they go. Ito me the average builder it’s hard to figure out where they hook up to. I’m sure others can figure it out but would be so simple if Dynon would just use wires that had where they go, like spruce does.
Works as stated. Necessary if you fly experimental within B class airports with 30 mile Mode C radius veil.
New EMS module corrected RF EMI issue on Skyview Classic display.
Q&A
Please note, Aircraft Spruce Canada's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce Canada assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.
You have the option of RG 400 or RG 58 coax cable. RG 400 is a higher quality cable but either will work.
No, the Skyview system is not TSO'd and is intended for experimental aircraft.
Dynon recommend the AV-74 our part number 11-05846.
They are standard density pins.
This would be part number 10-01196. The diagram is under the documents tab.
No, this system is not FAA Approved and is intended for use in experimental aircraft only.
Unfortunately, this unit cannot be installed in a certificated aircraft even as a back up. Please see the certified G5 for a qualifying unit.
Yes, you can find it on our website by keyword searching "Skyview HDX" or part # 10-06254.
Yes, these will include the connector kits.
The servo provided is the SV42EL.
