Q&A
Please note, Aircraft Spruce Canada's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce Canada assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.
Q: Is the GMC 507 compatible with my Aspen? Will it work with my ancient Century III autopilot?
No, this is only intended for use with the Garmin G3X system in experimental aircraft.
Q: Is this Garmin GMC 507 autopilot control approved for use in the M20J?
No, this is intended for use in experimental aircraft only.
Q: What is the difference between the Garmin GMC 507 and the 307? Will this work with 2 G5s or do I have to have a G3X?
The GMC 507 uses canbus for communication and has an extra TRK feature. The GMC 307 uses RS232 for communication. If you are using 2 G5's, per the manufacturer the GMC 507 is preferred.
Q: What are the dimensions of the Garmin GMC 507 autopilot control head?
Dimensions are: 6.25W x 2.10 H x 2.61 D (158.8 x 53.3 x 66.3 mm)
Q: Will this work with the new Gamin GNX™ 375?
No, this controller is designed for use in a G3X system utilizing a can-bus.
Q: Can this be used in certified aircraft with a certified G3X Touch? Is there a complete kit or do all parts have to be ordered separately. If so, what all is needed for a complete install?
No, we can only sell this item for experimental aircraft only.
Q: Online garmin sells a certificated version of the 507. Can’t that be used for autopilot control of the G3x in a certificated plane?
There is an FAA Approved version of this, however, this version, part # 11-16219 is the experimental version and cannot be installed in certified aircraft.
Q: What else has to be purchased to install the 507 and servos?
This autopilot is meant to work with the G3X system and the GMC 507 allows for dedicated autopilot controls.
Q: Is there mounting hardware that must be purchased separately?
Yes, Per Manual G3X/G3X Touch Rev AL, Page 14-1: The connector Kit P/N 11-16220 is required to install the unit. Please note: This unit is intended for use with the Garmin G3X System.
Q: Is the GMC 507 can be used with high torque servo from Trutrak Autopilot?
Garmin has their own servos that are required per the installation manual.
Q: Is the GMC 507 still only for experimental aircraft since it has several STCs for different airplane models?
This version of the GMC 507 is for experimental aircraft only. Certified versions must be purchased from the install shop.
Q: Will this unit work with my existing Trio Propilot Autopilot if I add the G3X?
This will only work with the Garmin Autopilot system.
Q: Can the GMC 507 be used as a stand alone controller to the servos for basic wing level control and altitude hold?
Per the manufacturer aside from the controller, you will need a G5 to drive it.
Q: Will the 507 link with the Aera series units like the 307 for VFR NAV functions?
The aera 660/760 are capable of connecting to an autopilot in an experimental application.
Q: Is the GMC 507 approved for the PA28 aircraft?
We cannot sell this unit for certified aircraft installations. Certified installs must purchase from the authorized Garmin install shop. We sell the G3X system for experimental aircraft only.
Q: Is the cutout the same size for the 307 and the 507? What are the measurements?
The cutout is the same. 6.25 inches X 2.10 inches. The difference is in the depth.
Q: Is there an install kit when connecting too 2 x G5s instead of the G3X?
It would use the same connector kit.
Q: What comes in the box for part # 11-16219?
This is only the control head. The connector kit is a separate item.
Q: To clarify, the GMC 507 will work with G5s, correct? If so then a G3X is not required?
Yes, the GMC 507 will work alone with the G5, a G3X is not required.
Q: Does the pitch control only work with a Garmin servo or can it operate an electric trim system with a moveable stabilizer?
The GSA28 servos can be used to control aircraft electric trim motors.
Q: One of the questions asks about interfacing with the Garmin 375 GNX. The answer says that that it does not integrate with that. However, the Garmin website specifically states it can be integrated with the 375. See this link and let us know why this product (gmc 507) would not work with the 375. https://www.garmin.com/en-US/p/577174
Per Garmin: We are having trouble understanding the exact question here. If it is, can the GNX 375 can be connected directly to an autopilot? Then the answer is no.
Q: Do you sell the GMC 307 install rack per Garmin manual? The GMC 507 Install Rack (115-02774-00) is to be used when installing the GMC 507 unit into a radio stack.
The rack is not included. We do offer it under part number # 11-19441.
Q: Can this device be driven by an MGL Avionics iefis explorer wich also has a can bus communication network instead of the Garmin G5?
No this will not. per MGL tech
Q: Will the gmc 507 work with an aera 796?
No, this is not designed to work with the 796.