Dash No. | MS No. | Dia. (in.) |
Length (in.) |
Recommended Drill Size |
Part No. | Price | Buy |
---|---|---|---|---|---|---|---|
AN535-00-2 | MS21318-1 | .060 | 1/8 | #55 (0.52) | 04-01246 | $0.13 | |
AN535-00-3 | MS21318-2 | .060 | 3/16 | #55 (.052) | 04-01247 | $0.10 | |
AN535-00-4 | MS21318-3 | .060 | 1/4 | #55 (.052) | MS21318-00-4 | $1.20 | |
AN535-0-2 | MS21318-7 | .075 | 1/8 | #51 (.067) | 04-01248 | $0.10 | |
AN535-0-3 | MS21318-8 | .075 | 3/16 | #51 (.067) | 04-01249 | $0.10 | |
AN535-0-4 | MS21318-9 | .075 | 1/4 | #51 (.067) | MS21318-9 | $0.19 | |
AN535-2-2 | MS21318-13 | .100 | 1/8 | #44 (0.86) | 04-01250 | $0.13 | |
AN535-2-3 | MS21318-14 | .100 | 3/16 | #44 (0.86) | MS21318-2-3 | $0.10 | |
AN535-2-4 | MS21318-15 | .100 | 1/4 | #44 (0.86) | MS21318-2-4 | $0.10 | |
AN535-4-3 | MS21318-20 | .116 | 3/16 | #37 (.104) | 04-01251 | $0.13 | |
AN535-4-4 | MS21318-21 | .116 | 1/4 | #37 (.104) | MS21318-4-4 | $0.13 | |
AN535-4-5 | MS21318-22 | .116 | 5/16 | #37 (.104) | 04-01252 | $0.21 |
Hardened steel screws to make permanent fastenings to ferrous and non-ferrous castings, heavy gauge steel, plastics, etc. Cadmium plated. |
they are the wrong size diameter. I need .100
MS21318-15,Screw AN535-2-4
Great rivets
MS21318-15,Screw AN535-2-4
Great rivets, works perfectly
MS21318-9 Screw,Drv AN535-0-4
Perfect fit, works great
Screw,Drive MS21318-21
Great rivets, if you use these you will never go back to the ones you were using
Screw AN535-4-5 / MS21318-22
Very good quality screw rivets, fit perfectly,easy to use
Screw,Drive MS21318-21
AN535-00-2 Screw MS21318-1
Screw MS21318-14 (AN535-2-3)
MS21318-15,Screw AN535-2-4
MS21318-9 Screw,Drv AN535-0-4
Please note, Aircraft Spruce Canada's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce Canada assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.
These are measured from below the head to the tip.